Fleck (61454-0) Injector #0 Red for 7000 SXT for 12" to 13" Tanks
Fleck 61454-0 Injector #0 Red for 7000 SXT
Precision-calibrated injector for 12" to 13" diameter softener tanks, engineered to match brine draw rates with tank volume for optimal regeneration efficiency
Injector sizing determines brine flow and regeneration quality
Red #0 Sizing
Factory-calibrated orifice matched to 12"-13" tank diameters, ensuring correct venturi suction for brine draw cycles without over or under-feeding resin beds
7000 SXT Spec
Designed specifically for Fleck 7000 SXT control valves, with threading and flow characteristics matched to valve body geometry and cycle timing
Venturi Principle
Creates controlled vacuum through water flow constriction, pulling brine solution from tank at precise rate for complete resin regeneration without waste
Field Serviceable
Direct replacement part that installs without special tools, restoring proper brine draw when original injector wears or becomes obstructed with mineral buildup
Confirmed valve and tank fit
This Fleck 61454-0 Red Injector #0 is engineered for use with Fleck 7000 SXT control valves installed on water softener tanks measuring 12 inches to 13 inches in diameter. Tank diameter determines required injector size because larger tanks need stronger vacuum pull to draw brine from greater distances. Using the wrong injector size results in incomplete regeneration or salt waste. Verify your tank diameter before ordering.
When to inspect or replace
Visual Inspection
Remove and examine injector throat for mineral scale, iron staining, or debris obstruction that reduces venturi suction
Replacement Cycle
Replace injector if softener fails to draw brine, leaves salt bridge intact, or shows incomplete regeneration despite proper settings
Hard Water Returns
If water hardness increases suddenly and tank has salt, check injector function before assuming resin failure or valve malfunction
Genuine Fleck OEM
Factory part with exact specifications, not aftermarket approximation
Tank-Matched Sizing
Engineered for 12"-13" diameter tanks, ensuring proper brine draw rate
Restores Performance
Returns regeneration efficiency to original factory specifications
Simple Installation
Threads directly into 7000 SXT valve body without modification
Fleck 61454-0 Injector #0 Red for 7000 SXT
Precision-calibrated injector for 12" to 13" diameter softener tanks, engineered to match brine draw rates with tank volume for optimal regeneration efficiency
Injector sizing determines brine flow and regeneration quality
Red #0 Sizing
Factory-calibrated orifice matched to 12"-13" tank diameters, ensuring correct venturi suction for brine draw cycles without over or under-feeding resin beds
7000 SXT Spec
Designed specifically for Fleck 7000 SXT control valves, with threading and flow characteristics matched to valve body geometry and cycle timing
Venturi Principle
Creates controlled vacuum through water flow constriction, pulling brine solution from tank at precise rate for complete resin regeneration without waste
Field Serviceable
Direct replacement part that installs without special tools, restoring proper brine draw when original injector wears or becomes obstructed with mineral buildup
Confirmed valve and tank fit
This Fleck 61454-0 Red Injector #0 is engineered for use with Fleck 7000 SXT control valves installed on water softener tanks measuring 12 inches to 13 inches in diameter. Tank diameter determines required injector size because larger tanks need stronger vacuum pull to draw brine from greater distances. Using the wrong injector size results in incomplete regeneration or salt waste. Verify your tank diameter before ordering.
When to inspect or replace
Visual Inspection
Remove and examine injector throat for mineral scale, iron staining, or debris obstruction that reduces venturi suction
Replacement Cycle
Replace injector if softener fails to draw brine, leaves salt bridge intact, or shows incomplete regeneration despite proper settings
Hard Water Returns
If water hardness increases suddenly and tank has salt, check injector function before assuming resin failure or valve malfunction
Genuine Fleck OEM
Factory part with exact specifications, not aftermarket approximation
Tank-Matched Sizing
Engineered for 12"-13" diameter tanks, ensuring proper brine draw rate
Restores Performance
Returns regeneration efficiency to original factory specifications
Simple Installation
Threads directly into 7000 SXT valve body without modification
Original: $29.32
-65%$29.32
$10.26Description
Fleck 61454-0 Injector #0 Red for 7000 SXT
Precision-calibrated injector for 12" to 13" diameter softener tanks, engineered to match brine draw rates with tank volume for optimal regeneration efficiency
Injector sizing determines brine flow and regeneration quality
Red #0 Sizing
Factory-calibrated orifice matched to 12"-13" tank diameters, ensuring correct venturi suction for brine draw cycles without over or under-feeding resin beds
7000 SXT Spec
Designed specifically for Fleck 7000 SXT control valves, with threading and flow characteristics matched to valve body geometry and cycle timing
Venturi Principle
Creates controlled vacuum through water flow constriction, pulling brine solution from tank at precise rate for complete resin regeneration without waste
Field Serviceable
Direct replacement part that installs without special tools, restoring proper brine draw when original injector wears or becomes obstructed with mineral buildup
Confirmed valve and tank fit
This Fleck 61454-0 Red Injector #0 is engineered for use with Fleck 7000 SXT control valves installed on water softener tanks measuring 12 inches to 13 inches in diameter. Tank diameter determines required injector size because larger tanks need stronger vacuum pull to draw brine from greater distances. Using the wrong injector size results in incomplete regeneration or salt waste. Verify your tank diameter before ordering.
When to inspect or replace
Visual Inspection
Remove and examine injector throat for mineral scale, iron staining, or debris obstruction that reduces venturi suction
Replacement Cycle
Replace injector if softener fails to draw brine, leaves salt bridge intact, or shows incomplete regeneration despite proper settings
Hard Water Returns
If water hardness increases suddenly and tank has salt, check injector function before assuming resin failure or valve malfunction
Genuine Fleck OEM
Factory part with exact specifications, not aftermarket approximation
Tank-Matched Sizing
Engineered for 12"-13" diameter tanks, ensuring proper brine draw rate
Restores Performance
Returns regeneration efficiency to original factory specifications
Simple Installation
Threads directly into 7000 SXT valve body without modification
