Clack (V3010-15E)-C-Series Injector, Black, 16" Downflow/21" Upflow Tank Size
C-Series Injector for V3010-15E Control Valves
Black injector sized for 16" downflow or 21" upflow softener tanks. Maintains consistent venturi pressure for reliable brine draw in residential and light commercial water softening systems.
Precision venturi engineering for the regeneration cycle
Sized for Tank Diameter
Black injector matches the flow dynamics of 16" downflow or 21" upflow resin tanks, ensuring proper brine suction during regeneration without over or under-drawing.
OEM Clack Engineering
Genuine Clack component designed to exact tolerances for the V3010-15E valve body. Consistent venturi geometry eliminates guesswork in brine eductor performance.
Critical Regeneration Part
The injector creates the vacuum that pulls brine into the resin tank. Worn or incorrect injectors lead to incomplete regeneration and early resin exhaustion.
Field Replaceable
Swaps into the valve body without special tools. Black color coding helps identify the correct size during service calls or system upgrades.
Clack V3010-15E valve systems with 16" or 21" tanks
This injector fits Clack V3010-15E control valves paired with 16-inch diameter downflow softener tanks or 21-inch diameter upflow tanks. Verify your tank size before ordering—injector sizing must match tank diameter for proper brine draw. Not interchangeable with other Clack injector colors or sizes. Check your valve manual or existing injector color if replacing a worn component.
Inspect annually, replace as needed
Visual Inspection
Check injector throat for mineral buildup or debris during routine valve service. Clean with white vinegar if scaling is present.
Replacement Interval
Replace injector if regeneration cycles run long, brine tank doesn't draw down, or resin capacity drops. Wear from abrasive water may require earlier replacement.
Tank Size Changes
Install the correct color-coded injector any time you upgrade or replace the resin tank. Mismatched sizing causes regeneration failures.
OEM Quality
Genuine Clack component, not an aftermarket substitute
Exact Sizing
Tank-specific flow rates for reliable brine draw every cycle
Simple Swap
Drops into valve body without plumbing modifications
Regeneration Insurance
Prevents costly resin replacement from incomplete cycles
C-Series Injector for V3010-15E Control Valves
Black injector sized for 16" downflow or 21" upflow softener tanks. Maintains consistent venturi pressure for reliable brine draw in residential and light commercial water softening systems.
Precision venturi engineering for the regeneration cycle
Sized for Tank Diameter
Black injector matches the flow dynamics of 16" downflow or 21" upflow resin tanks, ensuring proper brine suction during regeneration without over or under-drawing.
OEM Clack Engineering
Genuine Clack component designed to exact tolerances for the V3010-15E valve body. Consistent venturi geometry eliminates guesswork in brine eductor performance.
Critical Regeneration Part
The injector creates the vacuum that pulls brine into the resin tank. Worn or incorrect injectors lead to incomplete regeneration and early resin exhaustion.
Field Replaceable
Swaps into the valve body without special tools. Black color coding helps identify the correct size during service calls or system upgrades.
Clack V3010-15E valve systems with 16" or 21" tanks
This injector fits Clack V3010-15E control valves paired with 16-inch diameter downflow softener tanks or 21-inch diameter upflow tanks. Verify your tank size before ordering—injector sizing must match tank diameter for proper brine draw. Not interchangeable with other Clack injector colors or sizes. Check your valve manual or existing injector color if replacing a worn component.
Inspect annually, replace as needed
Visual Inspection
Check injector throat for mineral buildup or debris during routine valve service. Clean with white vinegar if scaling is present.
Replacement Interval
Replace injector if regeneration cycles run long, brine tank doesn't draw down, or resin capacity drops. Wear from abrasive water may require earlier replacement.
Tank Size Changes
Install the correct color-coded injector any time you upgrade or replace the resin tank. Mismatched sizing causes regeneration failures.
OEM Quality
Genuine Clack component, not an aftermarket substitute
Exact Sizing
Tank-specific flow rates for reliable brine draw every cycle
Simple Swap
Drops into valve body without plumbing modifications
Regeneration Insurance
Prevents costly resin replacement from incomplete cycles
Description
C-Series Injector for V3010-15E Control Valves
Black injector sized for 16" downflow or 21" upflow softener tanks. Maintains consistent venturi pressure for reliable brine draw in residential and light commercial water softening systems.
Precision venturi engineering for the regeneration cycle
Sized for Tank Diameter
Black injector matches the flow dynamics of 16" downflow or 21" upflow resin tanks, ensuring proper brine suction during regeneration without over or under-drawing.
OEM Clack Engineering
Genuine Clack component designed to exact tolerances for the V3010-15E valve body. Consistent venturi geometry eliminates guesswork in brine eductor performance.
Critical Regeneration Part
The injector creates the vacuum that pulls brine into the resin tank. Worn or incorrect injectors lead to incomplete regeneration and early resin exhaustion.
Field Replaceable
Swaps into the valve body without special tools. Black color coding helps identify the correct size during service calls or system upgrades.
Clack V3010-15E valve systems with 16" or 21" tanks
This injector fits Clack V3010-15E control valves paired with 16-inch diameter downflow softener tanks or 21-inch diameter upflow tanks. Verify your tank size before ordering—injector sizing must match tank diameter for proper brine draw. Not interchangeable with other Clack injector colors or sizes. Check your valve manual or existing injector color if replacing a worn component.
Inspect annually, replace as needed
Visual Inspection
Check injector throat for mineral buildup or debris during routine valve service. Clean with white vinegar if scaling is present.
Replacement Interval
Replace injector if regeneration cycles run long, brine tank doesn't draw down, or resin capacity drops. Wear from abrasive water may require earlier replacement.
Tank Size Changes
Install the correct color-coded injector any time you upgrade or replace the resin tank. Mismatched sizing causes regeneration failures.
OEM Quality
Genuine Clack component, not an aftermarket substitute
Exact Sizing
Tank-specific flow rates for reliable brine draw every cycle
Simple Swap
Drops into valve body without plumbing modifications
Regeneration Insurance
Prevents costly resin replacement from incomplete cycles
