Filmtec (TW30-4040) Tap Water Membrane 2,400 GPD @ 4" X 40"
Filmtec TW30-4040 Technical Details
| Model Number | TW30-4040 |
| Dimensions | 4 inches × 40 inches |
| Active Membrane Area | 78 ft² (7.2 m²) |
| Permeate Flow Rate | 2,400 GPD (9.1 m³/d) |
| Salt Rejection | 99.5% (stabilized) |
| Feed Spacer Thickness | 34 mil (thickest in class) |
| pH Cleaning Range | 1-13 |
| Test Conditions | 2000 ppm NaCl, 225 psi, 77°F, 15% recovery |
Installing Your TW30-4040 Membrane
- Flush the RO housing thoroughly with clean water before inserting the membrane element to remove any manufacturing debris or contaminants.
- Lubricate the brine seal and o-rings with clean water or glycerin, then slide the Filmtec TW30-4040 membrane into the pressure vessel with the brine seal end facing the concentrate port.
- Install end caps per your housing manufacturer's instructions, ensuring proper seal compression to prevent bypass.
- Start system at low pressure and gradually increase to operating pressure over 30-60 seconds, then flush permeate to drain for the first 30 minutes of operation.
- Monitor initial permeate TDS and flow rate, allowing 24-48 hours for the membrane to fully stabilize before making performance adjustments.
System Requirements & Applications
The Filmtec TW30-4040 is designed for tap water and low-fouling municipal feed sources with SDI less than 5. Compatible with standard 4-inch commercial housings rated for up to 300 psi, this membrane works in single or dual-element configurations for restaurants, offices, light industrial, aquarium systems, and other commercial applications requiring high-purity water. Not recommended for high-fouling water, brackish well water with elevated TDS, or seawater applications without consulting Dow's technical guidelines. Individual element flow may vary ±20% from nominal specifications.
Filmtec TW30-4040 Technical Details
| Model Number | TW30-4040 |
| Dimensions | 4 inches × 40 inches |
| Active Membrane Area | 78 ft² (7.2 m²) |
| Permeate Flow Rate | 2,400 GPD (9.1 m³/d) |
| Salt Rejection | 99.5% (stabilized) |
| Feed Spacer Thickness | 34 mil (thickest in class) |
| pH Cleaning Range | 1-13 |
| Test Conditions | 2000 ppm NaCl, 225 psi, 77°F, 15% recovery |
Installing Your TW30-4040 Membrane
- Flush the RO housing thoroughly with clean water before inserting the membrane element to remove any manufacturing debris or contaminants.
- Lubricate the brine seal and o-rings with clean water or glycerin, then slide the Filmtec TW30-4040 membrane into the pressure vessel with the brine seal end facing the concentrate port.
- Install end caps per your housing manufacturer's instructions, ensuring proper seal compression to prevent bypass.
- Start system at low pressure and gradually increase to operating pressure over 30-60 seconds, then flush permeate to drain for the first 30 minutes of operation.
- Monitor initial permeate TDS and flow rate, allowing 24-48 hours for the membrane to fully stabilize before making performance adjustments.
System Requirements & Applications
The Filmtec TW30-4040 is designed for tap water and low-fouling municipal feed sources with SDI less than 5. Compatible with standard 4-inch commercial housings rated for up to 300 psi, this membrane works in single or dual-element configurations for restaurants, offices, light industrial, aquarium systems, and other commercial applications requiring high-purity water. Not recommended for high-fouling water, brackish well water with elevated TDS, or seawater applications without consulting Dow's technical guidelines. Individual element flow may vary ±20% from nominal specifications.
Original: $449.00
-65%$449.00
$157.15Description
Filmtec TW30-4040 Technical Details
| Model Number | TW30-4040 |
| Dimensions | 4 inches × 40 inches |
| Active Membrane Area | 78 ft² (7.2 m²) |
| Permeate Flow Rate | 2,400 GPD (9.1 m³/d) |
| Salt Rejection | 99.5% (stabilized) |
| Feed Spacer Thickness | 34 mil (thickest in class) |
| pH Cleaning Range | 1-13 |
| Test Conditions | 2000 ppm NaCl, 225 psi, 77°F, 15% recovery |
Installing Your TW30-4040 Membrane
- Flush the RO housing thoroughly with clean water before inserting the membrane element to remove any manufacturing debris or contaminants.
- Lubricate the brine seal and o-rings with clean water or glycerin, then slide the Filmtec TW30-4040 membrane into the pressure vessel with the brine seal end facing the concentrate port.
- Install end caps per your housing manufacturer's instructions, ensuring proper seal compression to prevent bypass.
- Start system at low pressure and gradually increase to operating pressure over 30-60 seconds, then flush permeate to drain for the first 30 minutes of operation.
- Monitor initial permeate TDS and flow rate, allowing 24-48 hours for the membrane to fully stabilize before making performance adjustments.
System Requirements & Applications
The Filmtec TW30-4040 is designed for tap water and low-fouling municipal feed sources with SDI less than 5. Compatible with standard 4-inch commercial housings rated for up to 300 psi, this membrane works in single or dual-element configurations for restaurants, offices, light industrial, aquarium systems, and other commercial applications requiring high-purity water. Not recommended for high-fouling water, brackish well water with elevated TDS, or seawater applications without consulting Dow's technical guidelines. Individual element flow may vary ±20% from nominal specifications.
