HomeStore

Filmtec (XLE-2540) Low Energy Membrane 850 GPD 2.5" X 40"

Product image 1

Filmtec (XLE-2540) Low Energy Membrane 850 GPD 2.5" X 40"

The Filmtec XLE-2540 Low Energy Membrane delivers 850 GPD of high-purity water at the lowest operating pressure in its class, reducing energy costs without compromising performance. This 2.5" x 40" commercial RO membrane is tape-wrapped for economical installation in single or dual-element housings, offering the same high-quality construction as industrial hard-shell elements.
SPECIFICATIONS

Filmtec XLE-2540 Technical Details

Model Number XLE-2540
Dimensions 2.5" diameter x 40" length
Permeate Flow Rate 850 GPD (3.2 m³/d)
Salt Rejection 99.0% (stabilized)
Active Surface Area 28 ft² (2.6 m²)
Operating Pressure 100 psig (6.9 bar) nominal
pH Cleaning Range 1-13 (widest range available)
Construction Tape-wrapped (no hard shell)
INSTALLATION & USE

Installing Your XLE-2540 Membrane

  1. Remove the membrane housing end cap and carefully slide out any existing membrane element, noting the flow direction indicator.
  2. Lubricate the new XLE-2540 membrane O-rings with clean water or compatible lubricant, then insert the membrane into the housing with the brine seal facing the feed water inlet.
  3. Hand-tighten the end cap, ensuring proper seal alignment, then slowly pressurize the system and check for leaks before running a full flush cycle (discard permeate for the first 30-60 minutes).
  4. Monitor initial permeate quality and flow rate, allowing 24-48 hours for the membrane to stabilize and reach specified performance levels.
COMPATIBILITY

System Requirements

The Filmtec XLE-2540 is designed for commercial tap water applications with 500 ppm TDS or less, operating at 100 psig feed pressure with 8% recovery. Compatible with standard 2.5" x 40" membrane housings used in light commercial and small-scale industrial RO systems. This low-energy membrane is ideal for applications where reducing operating pressure and energy consumption is a priority, delivering maximum productivity with minimal power requirements. Test conditions: 500 ppm NaCl, 77°F, 100 psig. Individual element flow rates may vary ±20% from nominal specifications.

🔧 Pro tip: The XLE-2540's tape-wrapped design means no rigid outer shell to protect the membrane during handling. Always support the element along its full length when installing or removing it, and never lift or carry by one end alone to prevent internal damage to the membrane leaves.
The Filmtec XLE-2540 Low Energy Membrane delivers 850 GPD of high-purity water at the lowest operating pressure in its class, reducing energy costs without compromising performance. This 2.5" x 40" commercial RO membrane is tape-wrapped for economical installation in single or dual-element housings, offering the same high-quality construction as industrial hard-shell elements.
SPECIFICATIONS

Filmtec XLE-2540 Technical Details

Model Number XLE-2540
Dimensions 2.5" diameter x 40" length
Permeate Flow Rate 850 GPD (3.2 m³/d)
Salt Rejection 99.0% (stabilized)
Active Surface Area 28 ft² (2.6 m²)
Operating Pressure 100 psig (6.9 bar) nominal
pH Cleaning Range 1-13 (widest range available)
Construction Tape-wrapped (no hard shell)
INSTALLATION & USE

Installing Your XLE-2540 Membrane

  1. Remove the membrane housing end cap and carefully slide out any existing membrane element, noting the flow direction indicator.
  2. Lubricate the new XLE-2540 membrane O-rings with clean water or compatible lubricant, then insert the membrane into the housing with the brine seal facing the feed water inlet.
  3. Hand-tighten the end cap, ensuring proper seal alignment, then slowly pressurize the system and check for leaks before running a full flush cycle (discard permeate for the first 30-60 minutes).
  4. Monitor initial permeate quality and flow rate, allowing 24-48 hours for the membrane to stabilize and reach specified performance levels.
COMPATIBILITY

System Requirements

The Filmtec XLE-2540 is designed for commercial tap water applications with 500 ppm TDS or less, operating at 100 psig feed pressure with 8% recovery. Compatible with standard 2.5" x 40" membrane housings used in light commercial and small-scale industrial RO systems. This low-energy membrane is ideal for applications where reducing operating pressure and energy consumption is a priority, delivering maximum productivity with minimal power requirements. Test conditions: 500 ppm NaCl, 77°F, 100 psig. Individual element flow rates may vary ±20% from nominal specifications.

🔧 Pro tip: The XLE-2540's tape-wrapped design means no rigid outer shell to protect the membrane during handling. Always support the element along its full length when installing or removing it, and never lift or carry by one end alone to prevent internal damage to the membrane leaves.
$121.77

Original: $347.91

-65%
Filmtec (XLE-2540) Low Energy Membrane 850 GPD 2.5" X 40"—

$347.91

$121.77

Description

The Filmtec XLE-2540 Low Energy Membrane delivers 850 GPD of high-purity water at the lowest operating pressure in its class, reducing energy costs without compromising performance. This 2.5" x 40" commercial RO membrane is tape-wrapped for economical installation in single or dual-element housings, offering the same high-quality construction as industrial hard-shell elements.
SPECIFICATIONS

Filmtec XLE-2540 Technical Details

Model Number XLE-2540
Dimensions 2.5" diameter x 40" length
Permeate Flow Rate 850 GPD (3.2 m³/d)
Salt Rejection 99.0% (stabilized)
Active Surface Area 28 ft² (2.6 m²)
Operating Pressure 100 psig (6.9 bar) nominal
pH Cleaning Range 1-13 (widest range available)
Construction Tape-wrapped (no hard shell)
INSTALLATION & USE

Installing Your XLE-2540 Membrane

  1. Remove the membrane housing end cap and carefully slide out any existing membrane element, noting the flow direction indicator.
  2. Lubricate the new XLE-2540 membrane O-rings with clean water or compatible lubricant, then insert the membrane into the housing with the brine seal facing the feed water inlet.
  3. Hand-tighten the end cap, ensuring proper seal alignment, then slowly pressurize the system and check for leaks before running a full flush cycle (discard permeate for the first 30-60 minutes).
  4. Monitor initial permeate quality and flow rate, allowing 24-48 hours for the membrane to stabilize and reach specified performance levels.
COMPATIBILITY

System Requirements

The Filmtec XLE-2540 is designed for commercial tap water applications with 500 ppm TDS or less, operating at 100 psig feed pressure with 8% recovery. Compatible with standard 2.5" x 40" membrane housings used in light commercial and small-scale industrial RO systems. This low-energy membrane is ideal for applications where reducing operating pressure and energy consumption is a priority, delivering maximum productivity with minimal power requirements. Test conditions: 500 ppm NaCl, 77°F, 100 psig. Individual element flow rates may vary ±20% from nominal specifications.

🔧 Pro tip: The XLE-2540's tape-wrapped design means no rigid outer shell to protect the membrane during handling. Always support the element along its full length when installing or removing it, and never lift or carry by one end alone to prevent internal damage to the membrane leaves.
Filmtec (XLE-2540) Low Energy Membrane 850 GPD 2.5" X 40" | Isopure Water