HomeStore

Myron L (CS51) Conductivity Cell-10 FT.

Product image 1

Myron L (CS51) Conductivity Cell-10 FT.

The Myron L CS51 Conductivity Cell delivers lab-grade conductivity measurement with a 10-foot cable for flexible installation in tanks, process lines, or submersion applications. Built with 316 stainless steel and Teflon wetted materials, this general-purpose probe handles up to 20,000 µS/ppm with integrated temperature compensation for reliable accuracy.
SPECIFICATIONS

Myron L CS51 Technical Details

Model Number CS51
Cable Length 10 ft. / 3 meters
Measurement Range Up to 20,000 µS/ppm
Wetted Materials 316 stainless steel, Teflon
Process Connection 3/4" NPT bored-through swage fitting
Pressure Rating 100 psi at 100°C
Temperature Compensation Integral element, automatic
Seal Design Double EPR O-ring configuration
INSTALLATION & USE

How to Install the CS51 Cell

  1. Thread the 3/4" NPT swage fitting into your process line, tank wall, or standpipe. Apply thread sealant rated for your process temperature.
  2. Insert the CS51 probe through the fitting until seated. The double O-ring design creates a chemical-resistant seal without additional sealing compound.
  3. Route the 10 ft. cable to your Myron L meter or controller. Avoid sharp bends or pinch points along the cable run.
  4. For submersion configuration, reverse the swage fitting and mount to a standpipe. Ensure the probe tip is fully submerged during measurement.
  5. Verify electrical connection and allow time for temperature equilibration before calibration or measurement begins.
COMPATIBILITY

Works With Myron L Meters

The CS51 conductivity cell is designed for use with Myron L water quality meters and controllers that accept conductivity input. The integral temperature element enables automatic temperature compensation when connected to compatible meters. Field replaceable design allows for quick swap-outs without process shutdown. Suitable for general-purpose water quality monitoring in industrial, agricultural, and commercial applications where conductivity measurement up to 20,000 µS/ppm is required.

🔧 Pro Tip: The dual O-ring seal design puts the outer ring in contact with your process fluid while the inner ring stays protected. If you're working with aggressive chemicals, inspect the outer O-ring periodically and replace before it reaches the inner seal for maximum reliability.
The Myron L CS51 Conductivity Cell delivers lab-grade conductivity measurement with a 10-foot cable for flexible installation in tanks, process lines, or submersion applications. Built with 316 stainless steel and Teflon wetted materials, this general-purpose probe handles up to 20,000 µS/ppm with integrated temperature compensation for reliable accuracy.
SPECIFICATIONS

Myron L CS51 Technical Details

Model Number CS51
Cable Length 10 ft. / 3 meters
Measurement Range Up to 20,000 µS/ppm
Wetted Materials 316 stainless steel, Teflon
Process Connection 3/4" NPT bored-through swage fitting
Pressure Rating 100 psi at 100°C
Temperature Compensation Integral element, automatic
Seal Design Double EPR O-ring configuration
INSTALLATION & USE

How to Install the CS51 Cell

  1. Thread the 3/4" NPT swage fitting into your process line, tank wall, or standpipe. Apply thread sealant rated for your process temperature.
  2. Insert the CS51 probe through the fitting until seated. The double O-ring design creates a chemical-resistant seal without additional sealing compound.
  3. Route the 10 ft. cable to your Myron L meter or controller. Avoid sharp bends or pinch points along the cable run.
  4. For submersion configuration, reverse the swage fitting and mount to a standpipe. Ensure the probe tip is fully submerged during measurement.
  5. Verify electrical connection and allow time for temperature equilibration before calibration or measurement begins.
COMPATIBILITY

Works With Myron L Meters

The CS51 conductivity cell is designed for use with Myron L water quality meters and controllers that accept conductivity input. The integral temperature element enables automatic temperature compensation when connected to compatible meters. Field replaceable design allows for quick swap-outs without process shutdown. Suitable for general-purpose water quality monitoring in industrial, agricultural, and commercial applications where conductivity measurement up to 20,000 µS/ppm is required.

🔧 Pro Tip: The dual O-ring seal design puts the outer ring in contact with your process fluid while the inner ring stays protected. If you're working with aggressive chemicals, inspect the outer O-ring periodically and replace before it reaches the inner seal for maximum reliability.
$346.30
Myron L (CS51) Conductivity Cell-10 FT.—
$346.30

Description

The Myron L CS51 Conductivity Cell delivers lab-grade conductivity measurement with a 10-foot cable for flexible installation in tanks, process lines, or submersion applications. Built with 316 stainless steel and Teflon wetted materials, this general-purpose probe handles up to 20,000 µS/ppm with integrated temperature compensation for reliable accuracy.
SPECIFICATIONS

Myron L CS51 Technical Details

Model Number CS51
Cable Length 10 ft. / 3 meters
Measurement Range Up to 20,000 µS/ppm
Wetted Materials 316 stainless steel, Teflon
Process Connection 3/4" NPT bored-through swage fitting
Pressure Rating 100 psi at 100°C
Temperature Compensation Integral element, automatic
Seal Design Double EPR O-ring configuration
INSTALLATION & USE

How to Install the CS51 Cell

  1. Thread the 3/4" NPT swage fitting into your process line, tank wall, or standpipe. Apply thread sealant rated for your process temperature.
  2. Insert the CS51 probe through the fitting until seated. The double O-ring design creates a chemical-resistant seal without additional sealing compound.
  3. Route the 10 ft. cable to your Myron L meter or controller. Avoid sharp bends or pinch points along the cable run.
  4. For submersion configuration, reverse the swage fitting and mount to a standpipe. Ensure the probe tip is fully submerged during measurement.
  5. Verify electrical connection and allow time for temperature equilibration before calibration or measurement begins.
COMPATIBILITY

Works With Myron L Meters

The CS51 conductivity cell is designed for use with Myron L water quality meters and controllers that accept conductivity input. The integral temperature element enables automatic temperature compensation when connected to compatible meters. Field replaceable design allows for quick swap-outs without process shutdown. Suitable for general-purpose water quality monitoring in industrial, agricultural, and commercial applications where conductivity measurement up to 20,000 µS/ppm is required.

🔧 Pro Tip: The dual O-ring seal design puts the outer ring in contact with your process fluid while the inner ring stays protected. If you're working with aggressive chemicals, inspect the outer O-ring periodically and replace before it reaches the inner seal for maximum reliability.
Myron L (CS51) Conductivity Cell-10 FT. | Isopure Water